Strenx performance steel

Strenx® 110 XF

Download data sheet

Dimension Range

Strenx® 110 XF is available in thicknesses of 0.079 - 0.393 inches (2-10 mm), and in widths up to 63 inches (1600 mm) as coil, slit coil and cut to length sheets in lengths up to 630 inches (16000 mm).

Mechanical Properties

The mechanical properties are tested in the transverse direction.

Bending is valid in both longitudinal and transverse direction.

If ordered according to ASTM A1011 specification the tensile testing is performed in the longitudinal direction and the guaranteed elongation is A50 min 14 %.

Impact Properties

Min. impact energy for longitudinal testing,
Charpy V 10x10 mm test specimen
Min. impact energy for longitudinal testing,
Charpy V 10x10 mm test specimen
20 ft-lbs / -40 °F

1)Impact testing according to EN ISO 148-1 is performed on thicknesses ≥ 0.236 inch. The specified minimum value corresponds to a full-size specimen.

Chemical Composition (ladle analysis)

C
(max %)
C
(max %)
0.12
Si
(max %)
0.03
Mn
(max %)
2.10
P
(max %)
0.025
S
(max %)
0.010
Al
(min %)
0.015
Nb
(max %)
0.09
V
(max %)
0.20
Ti
(max %)
0.15

1) Strenx XF is available with different levels of Si: from max 0.03%, up to max 0.28%. Max Si 0.03% is the standard version that is suitable for hot dip galvanizing with thin Zinc layers, and for products that will not be galvanized. If the material is to be hot-dip galvanized and a thicker Zinc layer is requested, this must be specified at the time of order.

2) Sum of Nb, V and Ti = 0.22% max.

Thickness

Tolerances according to Strenx® Thickness Guarantees.

Strenx® Guarantees offer considerably narrower thickness tolerances compared to EN 10 051. 

Length and Width

Width and length tolerances according to SSAB standard. The SSAB standard offer narrower width and length tolerances compared to EN 10 051. Length tolerances only applyfor cut to length sheets

Shape

Tolerances according to EN 10 051.

Narrower tolerances according to the SSAB standard are available on request 

Flatness

Tolerances according to Strenx® Flatness Guarantees Class A.

Strenx® Flatness Guarantees offer narrower tolerances compared to EN 10 051.

Flatness guarantees only applyfor cut to length sheets. 

Surface Properties

Delivery Conditions

Thermomechanically Rolled. Strenx® XF is available in as rolled or pickled surface condition with mill or cut edge.

Fabrication and Other Recommendations

Welding, bending and machining

Strenx® XF has good welding, cold forming and cutting performance. Strenx® 100 XF is a cold forming steel not suited for heat treatments at temperatures above 1080°F (580°C) since the material then may lose its guaranteed properties.

For information concerning fabrication, see SSAB´s brochures on www.ssab.com or consult Tech Support, [email protected].

Appropriate health and safety precautions must be taken when bending, welding, cutting, grinding or otherwise working on the product.

Strenx® 110 XF high-strength structural steel

Strenx® 110 XF is a cold forming high-strength structural steel. It is a thermomechanically rolled product with a minimum yield strength of 110 ksi. It is suitable for a wide range of structural applications, including equipment and components in the transport, lifting and agriculture industry. Strenx® 110 XF meets the requirements of EN 10149-2 S700MC, ASTM A1011 grade 100 and ASTM A1018 grade 100 and can be supplied according to all of these standards' specifications on request. Strenx® 110 XF is available in thicknesses of 0.079 - 0.393 inches, and in widths up to 63 inches as coil, slit coil and cut to length sheets in lengths up to 630 inches.

Get technical advice

Show specs in:

MetricImperial